Electronic Surge Protection
Surge Protector ESP 06D
Application:
Data/Signal
Type:
-
Current:
0.3A
Phase:
-
Let through Voltage (Up):
12V
Voltage:
6V
In-line Resistance:
9.4 ohm
Installation:
Connect in series with the data communication or signal lineeither near where it enters or leaves the building or close tothe equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth starpoint.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable for
most twisted pair signalling applications. Available for working voltages of up
to 6, 15, 30, 50 and 110 Volts. ESP TN suitable for Broadband, POTS, dial-up,
T1/E1, lease line and *DSL telephone applications. For use at boundaries up
to LPZ 0 to protect against flashover (typically the service entrance location)
through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 06E
Application:
Data/Signal
Type:
-
Current:
1.25A
Phase:
-
Let through Voltage (Up):
36V
Voltage:
6V
In-line Resistance:
1 ohm
Installation:
Connect in series with the data communication or signal line either near where it enters or leaves the building or close to the equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth star point. Install protectors either within an existing cabinet/ cubicle or in a separate enclosure.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable
for twisted pair signalling applications which require either a lower in-line resistance, an increased current or a higher bandwidth than the ESP D Series. Also suitable for DC power applications less than 1.25 Amps. Available for working voltages of up to 6, 15, 30, 50 and 110 Volts. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 06H
Application:
Data/Signal
Type:
1 ohm
Current:
4A
Phase:
-
Let through Voltage (Up):
12V
Voltage:
6V
In-line Resistance:
0.05 ohm
Installation:
Connect in series with the signal or data line either near where it enters or leaves the building or close to the equipment being protected. Install in a cabinet/cubicle close to the system’s earth star point.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable
for twisted pair signalling applications which require either a lower in-line resistance or an increased current than the ESP D or E Series. Also suitable for DC power applications less than 4 Amps. Available for working voltages of up to 6, 15, 30, 50 and 110 Volts. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 06Q
Application:
Data/Signal
Type:
-
Current:
0.75A
Phase:
-
Let through Voltage (Up):
15V
Voltage:
6V
In-line Resistance:
1 ohm
Installation:
Combined Category D, C, B tested protector (to BS EN 61643) suitable for 4 twisted pair lines. Available for working voltages of up to 6, 15, 30, 50 and 110 Volts. ESP TNQ suitable for Broadband, POTS, dial-up, T1/E1, lease line and *DSL telephone applications. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable for 4
twisted pair lines. Available for working voltages of up to 6, 15, 30, 50 and
110 Volts. ESP TNQ suitable for Broadband, POTS, dial-up, T1/E1, lease line and *DSL telephone applications. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive
Surge Protector ESP 15D
Application:
Data/Signal
Type:
-
Current:
0.3A
Phase:
-
Let through Voltage (Up):
25V
Voltage:
15V
In-line Resistance:
9.4 ohm
Installation:
Connect in series with the data communication or signal lineeither near where it enters or leaves the building or close tothe equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth starpoint.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable for
most twisted pair signalling applications. Available for working voltages of up
to 6, 15, 30, 50 and 110 Volts. ESP TN suitable for Broadband, POTS, dial-up,
T1/E1, lease line and *DSL telephone applications. For use at boundaries up
to LPZ 0 to protect against flashover (typically the service entrance location)
through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 15E
Application:
Data/Signal
Type:
-
Current:
1.25A
Phase:
-
Let through Voltage (Up):
39V
Voltage:
15V
In-line Resistance:
1 ohm
Installation:
Connect in series with the data communication or signal line either near where it enters or leaves the building or close to the equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth star point. Install protectors either within an existing cabinet/ cubicle or in a separate enclosure.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable
for twisted pair signalling applications which require either a lower in-line resistance, an increased current or a higher bandwidth than the ESP D Series. Also suitable for DC power applications less than 1.25 Amps. Available for working voltages of up to 6, 15, 30, 50 and 110 Volts. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 15H
Application:
Data/Signal
Type:
-
Current:
4A
Phase:
-
Let through Voltage (Up):
27.5V
Voltage:
15V
In-line Resistance:
0.05 ohm
Installation:
Connect in series with the data communication or signal line either near where it enters or leaves the building or close to the equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth star point. Install protectors either within an existing cabinet/ cubicle or in a separate enclosure.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable
for twisted pair signalling applications which require either a lower in-line resistance or an increased current than the ESP D or E Series. Also suitable for DC power applications less than 4 Amps. Available for working voltages of up to 6, 15, 30, 50 and 110 Volts. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 15Q
Application:
Data/Signal
Type:
-
Current:
0.75A
Phase:
-
Let through Voltage (Up):
28V
Voltage:
15V
In-line Resistance:
1 ohm
Installation:
Connect in series with the signal or data line either near where it enters or leaves the building or close to the equipment being protected. Install in a cabinet/cubicle close to the system’s earth star point.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable for 4
twisted pair lines. Available for working voltages of up to 6, 15, 30, 50 and
110 Volts. ESP TNQ suitable for Broadband, POTS, dial-up, T1/E1, lease line and *DSL telephone applications. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive
Surge Protector ESP 30D
Application:
Data/Signal
Type:
-
Current:
0.3A
Phase:
-
Let through Voltage (Up):
44V
Voltage:
30V
In-line Resistance:
9.4 ohm
Installation:
Connect in series with the data communication or signal lineeither near where it enters or leaves the building or close tothe equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth starpoint.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable for
most twisted pair signalling applications. Available for working voltages of up
to 6, 15, 30, 50 and 110 Volts. ESP TN suitable for Broadband, POTS, dial-up,
T1/E1, lease line and *DSL telephone applications. For use at boundaries up
to LPZ 0 to protect against flashover (typically the service entrance location)
through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 30E
Application:
Data/Signal
Type:
-
Current:
1.25A
Phase:
-
Let through Voltage (Up):
60V
Voltage:
30V
In-line Resistance:
1 ohm
Installation:
Connect in series with the data communication or signal line either near where it enters or leaves the building or close to the equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth star point. Install protectors either within an existing cabinet/ cubicle or in a separate enclosure.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable
for twisted pair signalling applications which require either a lower in-line resistance, an increased current or a higher bandwidth than the ESP D Series. Also suitable for DC power applications less than 1.25 Amps. Available for working voltages of up to 6, 15, 30, 50 and 110 Volts. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 30H
Application:
Data/Signal
Type:
-
Current:
4A
Phase:
-
Let through Voltage (Up):
46V
Voltage:
30V
In-line Resistance:
0.05 ohm
Installation:
Connect in series with the data communication or signal line either near where it enters or leaves the building or close to the equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth star point. Install protectors either within an existing cabinet/ cubicle or in a separate enclosure.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable
for twisted pair signalling applications which require either a lower in-line resistance or an increased current than the ESP D or E Series. Also suitable for DC power applications less than 4 Amps. Available for working voltages of up to 6, 15, 30, 50 and 110 Volts. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 30Q
Application:
Data/Signal
Type:
-
Current:
0.75A
Phase:
-
Let through Voltage (Up):
53V
Voltage:
30V
In-line Resistance:
1 ohm
Installation:
Connect in series with the signal or data line either near where it enters or leaves the building or close to the equipment being protected. Install in a cabinet/cubicle close to the system’s earth star point.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable for 4
twisted pair lines. Available for working voltages of up to 6, 15, 30, 50 and
110 Volts. ESP TNQ suitable for Broadband, POTS, dial-up, T1/E1, lease line and *DSL telephone applications. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive
Surge Protector ESP 50D
Application:
Data/Signal
Type:
-
Current:
0.3A
Phase:
-
Let through Voltage (Up):
78V
Voltage:
50V
In-line Resistance:
9.4 ohm
Installation:
Connect in series with the data communication or signal lineeither near where it enters or leaves the building or close tothe equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth starpoint.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable for
most twisted pair signalling applications. Available for working voltages of up
to 6, 15, 30, 50 and 110 Volts. ESP TN suitable for Broadband, POTS, dial-up,
T1/E1, lease line and *DSL telephone applications. For use at boundaries up
to LPZ 0 to protect against flashover (typically the service entrance location)
through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 50E
Application:
Data/Signal
Type:
-
Current:
1.25A
Phase:
-
Let through Voltage (Up):
86V
Voltage:
50V
In-line Resistance:
1 ohm
Installation:
Connect in series with the data communication or signal line either near where it enters or leaves the building or close to the equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth star point. Install protectors either within an existing cabinet/ cubicle or in a separate enclosure.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable
for twisted pair signalling applications which require either a lower in-line resistance, an increased current or a higher bandwidth than the ESP D Series. Also suitable for DC power applications less than 1.25 Amps. Available for working voltages of up to 6, 15, 30, 50 and 110 Volts. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 50H
Application:
Data/Signal
Type:
-
Current:
4A
Phase:
-
Let through Voltage (Up):
67V
Voltage:
50V
In-line Resistance:
0.05 ohm
Installation:
Connect in series with the data communication or signal line either near where it enters or leaves the building or close to the equipment being protected (e.g. within its control panel). Either way, it must be very close to the system’s earth star point. Install protectors either within an existing cabinet/ cubicle or in a separate enclosure.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable
for twisted pair signalling applications which require either a lower in-line resistance or an increased current than the ESP D or E Series. Also suitable for DC power applications less than 4 Amps. Available for working voltages of up to 6, 15, 30, 50 and 110 Volts. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive electronic equipment.
Surge Protector ESP 50Q
Application:
Data/Signal
Type:
-
Current:
0.75A
Phase:
-
Let through Voltage (Up):
84V
Voltage:
50V
In-line Resistance:
1 ohm
Installation:
Connect in series with the signal or data line either near where it enters or leaves the building or close to the equipment being protected. Install in a cabinet/cubicle close to the system’s earth star point.
Description:
Combined Category D, C, B tested protector (to BS EN 61643) suitable for 4
twisted pair lines. Available for working voltages of up to 6, 15, 30, 50 and
110 Volts. ESP TNQ suitable for Broadband, POTS, dial-up, T1/E1, lease line and *DSL telephone applications. For use at boundaries up to LPZ 0 to protect against flashover (typically the service entrance location) through to LPZ 3 to protect sensitive